Autel Maxidas DS708 cable connection with Vehicle

As we all know Autel Maxidas DS708 is a universal diagnostic tool which is for all car models. In the carry case, it contains 26 pieces of accessories. Then which piece of adapter to use? Although most users know it, I would like to share here.

Please look at the following diagram:

As the picture shown above, generally speaking, firstly, connect the main cable with DS708, then among all the adapters choose a corresponding adapter to connect with the vehicle, which adapter to choose, it depends on your car’s OBD diagnostic socket.

For more details, you can check: Autel Maxidas DS708 user manual PDF

Solve to MaxiDAS DS708 Fatal Application Error illegal operation

Question One:

I get one Autel MaxiDAS® DS708 Update Service Special for USA and Canada, after complete update, I got a message "Fatal Application Error", reading: Application AutoRun.exe has performed an illegal operation and will be shut down. If the problem persists, contact the program vendor. My machine Serial Number is DS010Q001035, as following picture shows:



Solutions from UOBD2 engineer:

Please insert the SD card into your computer and format the SD card, and then run the Autel Maxidas DS708 Update again.

However, if you didn't register your DS708, follow the next steps to register and update:

1). DS708 Register Wizard
Insert the SD card into your computer and run the Autel Maxidas DS708 Register Wizard. Follow the step2 to step4 in "B. Register on the scan tool" (turn to page 26 in the Maxidas DS708 English manual) to complete registration to SD card. Put the SD card back to the scan tool and restart it to finish registration procedure.

2). DS708 Update

Insert the SD card into your computer and run the Maxidas DS708 Update. There is a Register option in the log-in window. When click on it, it will automatically link to DS708 Register Wizard. Follow the step2 to step4 in "B. Register on the scan tool" (turn to page 26 of DS708 English manual) to complete registration to SD card. Put the SD card back to the scan tool and restart it to finish registration procedure.

Question Two:

After register Autel DS708, I go to update and got error message reading "no connection with the server, please check network connections, what's the reason?

Solution from UOBD2 Engineer:

Do you have Autel Maxidas DS708 connected to the internet? If the DS708 has been connected to the network, but can't update, advice you update DS708 on computer.

What is Autel MaxiDAS® DS708

Autel MaxiDAS® DS708 is covered 30 Asian, European and American car models. Language supporting: English, French, Spanish, Portuguese, Japanese and German. Computer requirement is Windows CE operating system. . DS708 projects accurate, comprehensive and fast diagnosis. It is compatible with the function of supporting all 5 OBDII protocols and all 9 test modes. Support innovative remote diagnose wirelessly. Automatic WIFI update is available in the new release software.


Autel Maxidas DS708 Feature and Function:

1.Autel Maxidas DS708 is extensive vehicle coverage for more than 30 domestic, Asian and European vehicle makes
2.DS708 has seep vehicle system coverage for ALL electronic systems
3.Maxidas ds708 has complete function capability including live data.
4.Unparalleled OBDII functionalities supports ALL 5 OBDII protocols and ALL 9 test modes
5.Automatic Wi-Fi updates available in new software releases
6.Innovative dual-processor technology for quicker diagnostics and boot-up
7.The genuine Windows CE operating system allows for more stable performances, better compatibility and expandability
8.Internet explorer brings internet resource of your choice at your fingertips
9.WIFI internet capability allows for wireless access throughout the workshop
10.Extremely easy-to-us with touch-screen operation and intuitive operation
11.Unique shop tough ergonomic design features multi-layered rubber protection and strong housing
12.Intelligent memory of vehicles for easy and quick diagnosis of tested vehicles
13.Captures, saves and prints screenshots for convenient troubleshooting
14.Displays live data in text, graph and analog for easy data review and analysis
15.Records and playbacks live data to pinpoint troubles of sensors and components
16.Innovative graph merging for easy and quick detection of intermittent problems
17.Automatic WIFI Data Logging for quick and accurate technical support and troubleshooting
18.Built-in overvoltage protection keeps the instrument and vehicle from unwanted damages
29.Creative remote diagnosis for convenient demonstrationand training
20.Powered by Autel® Uni-SCANTM technology with no need for extra adaptors or "keys"
21.Prints out recorded data any time and anywhere with Wi-Fi printing capability

Autel Maxidas DS708 FAQ

Q: I tried to register DS708, but not successfully, I got error message “found no service or DNS error”, the WIFI indicator light keep flashing.



A: There are mainly two ways to register.
The first way: use computer to register on www.maxidas.com, (NOTE: Please use the System/Help > about function to find out the Product Serial No. and Register Password. )
The second way: register on the scan tool. Before register on the scan tool, use the internet cable to connect DS708 and the computer.
The first time you start the scan tool, it will pop up a message box to advise user to register your tool, showing as follow. This message will display 30 seconds each time you power the tool up until properly registered.



For more details on how to step-by-step register, click http://www.autelscanner.org/ and turn to page 19- entitled “2.4. Register the Tool”.

Q: Where to update Autel MaxiDAS® DS708?
A: Go to update at DS708 official website: http://www.maxidas.com/, you could download software, update online, retrieve information and get warranty service.

Q: Can I download and update German version in the Autel official website?
A: yes, you can. You are allowed to customize one specific language among these languages: English, Spanish, French, German, Australia and Russian, but not accessible to switch to the language what you want when you use DS708.

Q: What is update cost one year later?
A: when you want to update DS708 one year later since you ordered DS708, please contact Autel customer service for the update cost.

Q: I bought Autel DS708 from you last year and always work well. But today I get error when I open DS708, I can’t open any window.
A: Did you register as member of Autel? Can you update on the computer? If the DS708 are accessible to update on the computer, insert the SD card into your computer and format the SD card, and then run the DS708 Update again.
However, if you didn’t register, follow the next steps to register and update:
1). DS708 Register Wizard
Insert the SD card into your computer and run the DS708 Register Wizard. Follow the step2 to step4 in “B. Register on the scan tool” (turn to page 26 in the DS708 English manual) to complete registration to SD card.
Put the SD card back to the scan tool and restart it to finish registration procedure.
2). DS708 Update
Insert the SD card into your computer and run the DS708 Update. There is a Register option in the log-in window. When click on it, it will automatically link to DS708 Register Wizard. Follow the step2 to step4 in “B. Register on the scan tool” (turn to page 26 of DS708 English manual) to complete registration to SD card.
Put the SD card back to the scan tool and restart it to finish registration procedure.

Q: After register Autel DS708, I go to update and got error message reading “no connection with the server, please check network connections, what’s the reason?
A: Do you have DS708 connected to the internet? If the DS708 has been connected to the network, but can’t update, advice you update DS708 on computer. Please step-by-step follow the DS708 update instruction http://www.autelscanner.org/

How to update Autel Maxidas Das708

Steps to update Autel Maxidas DS708:

一、Autel Maxidas DS708 Update Main Usage 

1. Upgrade with the programs which Autel company designate to get all the update files. 

2. It allows to uninstall the softwares that SD card has already installed before. 

二、Operation instructions 

1. Uncompress the package to current folder. 

2.Place the DS708 SD card into your computer. Copy and paste the“Scan”and”autorun.exe”files under the root directory of SD card. 

3.Run the program “manager-pc” on your PC according to the following promts on 

your computer. There comes a program called “updateclient” , then run it. You can see.

4. Choose all the package files and click “Update” to download them. (Or choose some according to your personal will.) They can be extracted automatically into your SD card after being downloaded completely. Please no worry and kindly wait for that. “Page up “and “Page down” allow you to view other options or information. If you have more than one DS708 and SD card to upgrade, please “select disk” to choose different SD cards. 

5.Uninstall Programs 

Under the “Installed Programs”menu, it allows people to delete the vehicles files which SD card installed before. 

6.”User Info” has the function to modify the login password. But it is disabled currently until the system is completed.

7.The website information and software version can be checked under the “Option” menu. It also allows people to find a path of the temporary directory to download files.

How to use Autel Maxidas DS708

Autel MaxiDAS ® DS708 setup:

Step 1: Insert the Memory Card

Make sure the SD Memory Card is inserted properly into the MaxiDAS DS708 card slot.
1. Insert the SD memory card with the metal contacts facing down and pointing toward
the tool.
2. Remove the card and insert it again if the DS708 SD card is not mounting properly.
Note: Do not force the SD card into the card slot. This may damage the card
slot.

Step 2: Connect the Hardware Model& Power Supply

To provide power to this unit, use an external power supply or simply connect Autel Maxidas ds708 unit to a vehicle with a communication cable. Press the power button once and wait until the system boots up. After a brief moment, the MaxiDAS Diagnostic Platform displays and the ds708 is now ready to operate. See Chapter 4 on page 10 to assist you to find the DLC on your vehicle.
Note: Autel Maxidas ds708 scan tool does not have a battery and can not be charged, make sure
the unit is connected to a power supply before using the scan tool.

Step 3: Diagnose the vehicle

A: Connect to the Vehicle

To perform diagnostic tests, select the vehicle you want to test, connect the autel ds708 diagnostic tool
to the vehicle’s data link connector (DLC) with a communication cable.
Refer to the following instruction to locate DLC on your vehicle.
The DLC is usually located 12 inches under instrument panel dash.



Explanation of Diagram Numbered Locations
Location Description
1 Underneath dashboard, under the steering
2 Underneath dashboard, between the driver-side door and steering column area
3 Underneath dashboard, between the steering column area and the center console
4 Dashboard instrument/gauge area, between the steering column and center console
5 Dashboard instrument/gauge area, between the driver-side door and steering column
6 Center console, vertical surface ( i.e., near radio and climate controls), left of/ on vehicle
centerline
7 Center console, vertical surface right of vehicle centerline or on passenger side of center
console.
8 Center console, horizontal surface (i.e., armrest, handbrake area), in front passenger area
9 Any location other than locations 1-8 ( i.e., passenger area, passenger side glove box)


B: Identifying the Vehicle

Option 1: Select manually from the autel maxidas ds708 main menu,
The following messages only show some of the possible options. During testing, only the options available for the vehicle and ECU being tested will appear on the screen. Select one of the attributes from each screen and highlight the attribute to enter to the next page.
The screens continue appearing until the selecting complete. Follow instruction on each screen that appears to find the access to the function test.
1. Select the group of the manufacturer by highlighting menu option. The manufacturers are categorized into three groups according to the locations (USA, European or
Asian).
2. Press the manufacturer key to enter a new screen. A dialog box pops up shows the loading process, wait until compete.
Possible 1: For some of the vehicle, identify vehicle process is not needed.
Component test screen appear at this stage already and allows you to perform the
component test.
Possible 2: For the others, continue selecting the vehicle from the scan tool is needed.
To identify the vehicle, you may need to complete a series of selections, which may include any of the followings. (Benz as an example) Select one of the attributes from each screen and highlight the attribute to enter to the next page. The screens continue appearing until the selecting process complete.
(All Model Series, 169 have been selected)
(As of 12/2005, Left hand steering have been selected)
(Sedan and Gasoline have been selected)
(167.031 A 150 has been selected and the communication screen shows)
Option 2: Select form the Vehicle Record (If the vehicle has Auto Scan function)
To identify a vehicle by vehicle record,
1. Click the Vehicle Record button.
2. Select the Vehicle ID from the list.
Note: This option is only available to those which have Auto Scan function, refer
to Chapter 5 Auto Scan (HONDA) on Page 23 for how to establish a vehicle
record access.
3. The following ds708 screen displays and asks for your confirmation, click Yes to select or
click No to exit.
4. The following screen shows the communication status.
5. The Information screen shows and asks you to input correct ODO value. Use the
virtual keyboard to enter.
1) Drag the virtual keyboard with stylus to relocate.
2) Use the keyboard to fill in the dialog box with all the information as desired.
3) Select OK to finish and close the dialog box.
Optionally, use the drop-down dialog box to find the vehicle if the previous recode is
available.
Option 3: Select by OBD II Quick Test
OBDII/ EOBD is used to provide a quick test for the users, in this section, the vehicle can
be tested directly without completing the vehicle identification process.


C: Diagnose the vehicle

During testing, only the options available for the vehicle and ECU being tested will appear on the screen. The diagnostic functions may cover any of the followings, read the screen and chose one of the options to perform a test.

Auto Scan

The Auto Scan does an automatic test of the ECU being tested and then displays
a summary of the test results. From the summary, you can access to the Function menu (Refer to 26) and view detailed test results, such as DTC descriptions and related repair information. To see the details, refer to Chapter 5 on page …

Diagnostic Trouble Codes

This is a shortcut that allows you to quickly access vehicle systems without
completing a Vehicle ID, so as to find out what repairs are needed. Also refer to
Chapter 6 for details on page…

Live Data

The Live Data function allows you to view the live (real time) PID data from the
vehicle’s computer module. For details, refer to Chapter 7 on page

Freeze Frame

The Freeze Fame function allows you view DataStream "Snapshots" that were
automatically recorded by the ECU when one or more DTCs occurred. By
viewing the actual data values from the time of a fault, you may be able to
determine what caused the fault. For details, refer to Chapter 8 on page.

Component Test

The Component Test function allows initiating a leak test for the vehicle’s EVAP
system. The scan tool itself does not perform the leak test, but commands the
vehicle’s on-board computer to start the test. Different vehicle manufacturers
might have different criteria and methods for stopping the test once it has been
started. Before starting the Component Test, refer to the vehicle service manual
for instructions to stop the test. For details, refer to Chapter 9 on page.

I/M Readiness

Refer to Chapter 10 on page… for detail.

O2 Mon. Test ( O2 Monitor Test)

OBD II regulations set by the SAE require that relevant vehicles monitor and test
the oxygen (O2) sensors to indentify problems related to fuel efficiency and
vehicle emissions. These tests are not on- demand tests and they are done
automatically when engine operating conditions are within specified limits. These
test results are saved in the on-boards computer’s memory.

More Details check: Autel Maxidas DS708 User Manual

http://www.autelscanner.org/

Autel Maxidas DS708 Component Introduction

1. DS708 Main Connection Port Connect to the mains for power supply of updating, printing data logging and internet access after disconnecting from the vehicle.

2. Diagnostic Socket Provides power supply and connection to the vehicle via diagnostic cables and connectors supplied.

3. Internet Connection Port Provides internet access for updating, printing and data logging and brings the internet resource of your choice at your fingertips.

4. ON/ OFF Button Powers on/ off the diagnostic tool.

5. DS708 LED Indicators

The three light-emitting diodes indicate certain system conditions,

Communication LED – Green LED light in middle shows when the unit is in service.

Wireless LAN activity LED – Green LED light in the left shows when a wireless local area network in enabled, flashes when data is being sent or received.

Main Power LED – Red LED light in the right shows when the unit is powered on.

6. DS708 SD Card Slot

The standard SD (Secure Digital) card slot enables the unit to read and write data to the card inserted in the slot. To use the software, insert the card with the metal contacts facing down and pointing toward the MaxiDAS.

Note: Do not force media into the SD card slot. This may damage the SD card slot. To Remove SD Card, press the card again and slot will pop out card automatically.

7. Stylus The Stylus is used for typing and selecting. To calibrating Touch Screen, refer to chapter 7 – 8, Calibrating Touch Screen.

8. Stand The built- in metal stand allows the unit to rest for hands-free viewing when extended. It is attached to the back of the scan tool and can be secured to the back again unit when not in use.

9. Handgrip The handgrips are attached to both sides of the MaxiDAS unit. Hold the handgrips to stabilize the unit while using. The handgrip also eliminates the damage when you drop the tool accidentally.

10. MaxiDAS 708 Label

The Label includes the notice and warning.

11. LCD Screen Displays the menus and data screens.

Important: Use the supplied stylus or plastic-tipped pens for touch screen display. Do not use pencil, pen or any sharp object on touch screen display.

12. Memory Card

The Memory Card contains the tool’s diagnostic software, applications and maximum of 4 Gigabytes storage.

Note: Do not remove the memory card while the unit is in service.

13. DLC Cables

The DLC (Data Link Connector) Cable is used to connect between the scan tool and vehicle’s DLC. Numbers of cables are provided; select the appropriate one for the vehicle being tested. An optional extension cable may also be used.

14. AC Power Supply

The AC power supply and power cord (12V and 3.33A) is used to power the scan tool from wall socket.

Author: http://www.autelscanner.org/