Showing posts with label Autel Maxidas DS708 User Manual. Show all posts
Showing posts with label Autel Maxidas DS708 User Manual. Show all posts
Monday, December 28, 2015
Sunday, December 27, 2015
Autel DS708 reset Toyota Camry 07-10 TPMS
The tire pressure warning light blinks for 1 minute and stays on to indicate a tire pressure monitoring system malfunction after driving for about 20 minutes. If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. Following part are the detail instructions on resetting Toyota Camry (2007-2010) TPMS (Tire Pressure Monitoring System) indicator light with Autel MaxiDAS DS708 diagnostic scanner.
Instruction:
Autel DS708 OBD2 diagnostic scan tool
Toyota Camry transmitter ID code
Ps: Where is the tire transmitter ID code located?
You need to copy the id code from the tire pressure sensor. It is stamped on the side of the sensor.)
Well install Autel DS708 software
Connect the DS708 scan tool with vehicle via OBD socket
Power on the device and browse to “System Menu”
Find out and locate “Tire Pressure Monitor” option in “System Menu”
Select Utility
Select ID Registration
The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code.
Registration will fail if the time limit is exceeded for any step. Press OK to proceed.
Press OK to begin the registration process.
The system warns that you have 5 minutes to complete 3 procedures:
—Input each transmitter ID code
—Input next transmitter ID code
—Wait all ID code are registered.
Manually enter the transmitter ID follow the system prompts, and press OK
Step 4 of 4
Input the transmitter ID Code
Total Tires: 4
Register Tires:1
Press OK to input another ID Code.
Enter 4 ID codes one by one until the system will display ID Registration is complete message.
Go back to “Function Menu”, select “Read Codes” and then erase fault codes.
TPMS indicator light has been disabled. The indicator light on dashboard go off.
More information please search: autel maxidas ds708
Thursday, August 28, 2014
Autel Maxidas DS708 cable connection with Vehicle
As we all know Autel Maxidas DS708 is a universal diagnostic tool which is for all car models. In the carry case, it contains 26 pieces of accessories. Then which piece of adapter to use? Although most users know it, I would like to share here.
Please look at the following diagram:
As the picture shown above, generally speaking, firstly, connect the main cable with DS708, then among all the adapters choose a corresponding adapter to connect with the vehicle, which adapter to choose, it depends on your car’s OBD diagnostic socket.
For more details, you can check: Autel Maxidas DS708 user manual PDF
Please look at the following diagram:
As the picture shown above, generally speaking, firstly, connect the main cable with DS708, then among all the adapters choose a corresponding adapter to connect with the vehicle, which adapter to choose, it depends on your car’s OBD diagnostic socket.
For more details, you can check: Autel Maxidas DS708 user manual PDF
Wednesday, August 13, 2014
How to use Autel Maxidas DS708
Autel MaxiDAS ® DS708 setup:
Step 1: Insert the Memory Card
Make sure the SD Memory Card is inserted properly into the MaxiDAS DS708 card slot.
1. Insert the SD memory card with the metal contacts facing down and pointing toward
the tool.
2. Remove the card and insert it again if the DS708 SD card is not mounting properly.
Note: Do not force the SD card into the card slot. This may damage the card
slot.
Step 2: Connect the Hardware Model& Power Supply
To provide power to this unit, use an external power supply or simply connect Autel Maxidas ds708 unit to a vehicle with a communication cable. Press the power button once and wait until the system boots up. After a brief moment, the MaxiDAS Diagnostic Platform displays and the ds708 is now ready to operate. See Chapter 4 on page 10 to assist you to find the DLC on your vehicle.
Note: Autel Maxidas ds708 scan tool does not have a battery and can not be charged, make sure
the unit is connected to a power supply before using the scan tool.
Step 3: Diagnose the vehicle
A: Connect to the Vehicle
To perform diagnostic tests, select the vehicle you want to test, connect the autel ds708 diagnostic tool
to the vehicle’s data link connector (DLC) with a communication cable.
Refer to the following instruction to locate DLC on your vehicle.
The DLC is usually located 12 inches under instrument panel dash.
Explanation of Diagram Numbered Locations
Location Description
1 Underneath dashboard, under the steering
2 Underneath dashboard, between the driver-side door and steering column area
3 Underneath dashboard, between the steering column area and the center console
4 Dashboard instrument/gauge area, between the steering column and center console
5 Dashboard instrument/gauge area, between the driver-side door and steering column
6 Center console, vertical surface ( i.e., near radio and climate controls), left of/ on vehicle
centerline
7 Center console, vertical surface right of vehicle centerline or on passenger side of center
console.
8 Center console, horizontal surface (i.e., armrest, handbrake area), in front passenger area
9 Any location other than locations 1-8 ( i.e., passenger area, passenger side glove box)
B: Identifying the Vehicle
Option 1: Select manually from the autel maxidas ds708 main menu,
The following messages only show some of the possible options. During testing, only the options available for the vehicle and ECU being tested will appear on the screen. Select one of the attributes from each screen and highlight the attribute to enter to the next page.
The screens continue appearing until the selecting complete. Follow instruction on each screen that appears to find the access to the function test.
1. Select the group of the manufacturer by highlighting menu option. The manufacturers are categorized into three groups according to the locations (USA, European or
Asian).
2. Press the manufacturer key to enter a new screen. A dialog box pops up shows the loading process, wait until compete.
Possible 1: For some of the vehicle, identify vehicle process is not needed.
Component test screen appear at this stage already and allows you to perform the
component test.
Possible 2: For the others, continue selecting the vehicle from the scan tool is needed.
To identify the vehicle, you may need to complete a series of selections, which may include any of the followings. (Benz as an example) Select one of the attributes from each screen and highlight the attribute to enter to the next page. The screens continue appearing until the selecting process complete.
(All Model Series, 169 have been selected)
(As of 12/2005, Left hand steering have been selected)
(Sedan and Gasoline have been selected)
(167.031 A 150 has been selected and the communication screen shows)
Option 2: Select form the Vehicle Record (If the vehicle has Auto Scan function)
To identify a vehicle by vehicle record,
1. Click the Vehicle Record button.
2. Select the Vehicle ID from the list.
Note: This option is only available to those which have Auto Scan function, refer
to Chapter 5 Auto Scan (HONDA) on Page 23 for how to establish a vehicle
record access.
3. The following ds708 screen displays and asks for your confirmation, click Yes to select or
click No to exit.
4. The following screen shows the communication status.
5. The Information screen shows and asks you to input correct ODO value. Use the
virtual keyboard to enter.
1) Drag the virtual keyboard with stylus to relocate.
2) Use the keyboard to fill in the dialog box with all the information as desired.
3) Select OK to finish and close the dialog box.
Optionally, use the drop-down dialog box to find the vehicle if the previous recode is
available.
Option 3: Select by OBD II Quick Test
OBDII/ EOBD is used to provide a quick test for the users, in this section, the vehicle can
be tested directly without completing the vehicle identification process.
C: Diagnose the vehicle
During testing, only the options available for the vehicle and ECU being tested will appear on the screen. The diagnostic functions may cover any of the followings, read the screen and chose one of the options to perform a test.
Auto Scan
The Auto Scan does an automatic test of the ECU being tested and then displays
a summary of the test results. From the summary, you can access to the Function menu (Refer to 26) and view detailed test results, such as DTC descriptions and related repair information. To see the details, refer to Chapter 5 on page …
Diagnostic Trouble Codes
This is a shortcut that allows you to quickly access vehicle systems without
completing a Vehicle ID, so as to find out what repairs are needed. Also refer to
Chapter 6 for details on page…
Live Data
The Live Data function allows you to view the live (real time) PID data from the
vehicle’s computer module. For details, refer to Chapter 7 on page
Freeze Frame
The Freeze Fame function allows you view DataStream "Snapshots" that were
automatically recorded by the ECU when one or more DTCs occurred. By
viewing the actual data values from the time of a fault, you may be able to
determine what caused the fault. For details, refer to Chapter 8 on page.
Component Test
The Component Test function allows initiating a leak test for the vehicle’s EVAP
system. The scan tool itself does not perform the leak test, but commands the
vehicle’s on-board computer to start the test. Different vehicle manufacturers
might have different criteria and methods for stopping the test once it has been
started. Before starting the Component Test, refer to the vehicle service manual
for instructions to stop the test. For details, refer to Chapter 9 on page.
I/M Readiness
Refer to Chapter 10 on page… for detail.
O2 Mon. Test ( O2 Monitor Test)
OBD II regulations set by the SAE require that relevant vehicles monitor and test
the oxygen (O2) sensors to indentify problems related to fuel efficiency and
vehicle emissions. These tests are not on- demand tests and they are done
automatically when engine operating conditions are within specified limits. These
test results are saved in the on-boards computer’s memory.
More Details check: Autel Maxidas DS708 User Manual
http://www.autelscanner.org/
Step 1: Insert the Memory Card
Make sure the SD Memory Card is inserted properly into the MaxiDAS DS708 card slot.
1. Insert the SD memory card with the metal contacts facing down and pointing toward
the tool.
2. Remove the card and insert it again if the DS708 SD card is not mounting properly.
Note: Do not force the SD card into the card slot. This may damage the card
slot.
Step 2: Connect the Hardware Model& Power Supply
To provide power to this unit, use an external power supply or simply connect Autel Maxidas ds708 unit to a vehicle with a communication cable. Press the power button once and wait until the system boots up. After a brief moment, the MaxiDAS Diagnostic Platform displays and the ds708 is now ready to operate. See Chapter 4 on page 10 to assist you to find the DLC on your vehicle.
Note: Autel Maxidas ds708 scan tool does not have a battery and can not be charged, make sure
the unit is connected to a power supply before using the scan tool.
Step 3: Diagnose the vehicle
A: Connect to the Vehicle
To perform diagnostic tests, select the vehicle you want to test, connect the autel ds708 diagnostic tool
to the vehicle’s data link connector (DLC) with a communication cable.
Refer to the following instruction to locate DLC on your vehicle.
The DLC is usually located 12 inches under instrument panel dash.
Explanation of Diagram Numbered Locations
Location Description
1 Underneath dashboard, under the steering
2 Underneath dashboard, between the driver-side door and steering column area
3 Underneath dashboard, between the steering column area and the center console
4 Dashboard instrument/gauge area, between the steering column and center console
5 Dashboard instrument/gauge area, between the driver-side door and steering column
6 Center console, vertical surface ( i.e., near radio and climate controls), left of/ on vehicle
centerline
7 Center console, vertical surface right of vehicle centerline or on passenger side of center
console.
8 Center console, horizontal surface (i.e., armrest, handbrake area), in front passenger area
9 Any location other than locations 1-8 ( i.e., passenger area, passenger side glove box)
B: Identifying the Vehicle
Option 1: Select manually from the autel maxidas ds708 main menu,
The following messages only show some of the possible options. During testing, only the options available for the vehicle and ECU being tested will appear on the screen. Select one of the attributes from each screen and highlight the attribute to enter to the next page.
The screens continue appearing until the selecting complete. Follow instruction on each screen that appears to find the access to the function test.
1. Select the group of the manufacturer by highlighting menu option. The manufacturers are categorized into three groups according to the locations (USA, European or
Asian).
2. Press the manufacturer key to enter a new screen. A dialog box pops up shows the loading process, wait until compete.
Possible 1: For some of the vehicle, identify vehicle process is not needed.
Component test screen appear at this stage already and allows you to perform the
component test.
Possible 2: For the others, continue selecting the vehicle from the scan tool is needed.
To identify the vehicle, you may need to complete a series of selections, which may include any of the followings. (Benz as an example) Select one of the attributes from each screen and highlight the attribute to enter to the next page. The screens continue appearing until the selecting process complete.
(All Model Series, 169 have been selected)
(As of 12/2005, Left hand steering have been selected)
(Sedan and Gasoline have been selected)
(167.031 A 150 has been selected and the communication screen shows)
Option 2: Select form the Vehicle Record (If the vehicle has Auto Scan function)
To identify a vehicle by vehicle record,
1. Click the Vehicle Record button.
2. Select the Vehicle ID from the list.
Note: This option is only available to those which have Auto Scan function, refer
to Chapter 5 Auto Scan (HONDA) on Page 23 for how to establish a vehicle
record access.
3. The following ds708 screen displays and asks for your confirmation, click Yes to select or
click No to exit.
4. The following screen shows the communication status.
5. The Information screen shows and asks you to input correct ODO value. Use the
virtual keyboard to enter.
1) Drag the virtual keyboard with stylus to relocate.
2) Use the keyboard to fill in the dialog box with all the information as desired.
3) Select OK to finish and close the dialog box.
Optionally, use the drop-down dialog box to find the vehicle if the previous recode is
available.
Option 3: Select by OBD II Quick Test
OBDII/ EOBD is used to provide a quick test for the users, in this section, the vehicle can
be tested directly without completing the vehicle identification process.
C: Diagnose the vehicle
During testing, only the options available for the vehicle and ECU being tested will appear on the screen. The diagnostic functions may cover any of the followings, read the screen and chose one of the options to perform a test.
Auto Scan
The Auto Scan does an automatic test of the ECU being tested and then displays
a summary of the test results. From the summary, you can access to the Function menu (Refer to 26) and view detailed test results, such as DTC descriptions and related repair information. To see the details, refer to Chapter 5 on page …
Diagnostic Trouble Codes
This is a shortcut that allows you to quickly access vehicle systems without
completing a Vehicle ID, so as to find out what repairs are needed. Also refer to
Chapter 6 for details on page…
Live Data
The Live Data function allows you to view the live (real time) PID data from the
vehicle’s computer module. For details, refer to Chapter 7 on page
Freeze Frame
The Freeze Fame function allows you view DataStream "Snapshots" that were
automatically recorded by the ECU when one or more DTCs occurred. By
viewing the actual data values from the time of a fault, you may be able to
determine what caused the fault. For details, refer to Chapter 8 on page.
Component Test
The Component Test function allows initiating a leak test for the vehicle’s EVAP
system. The scan tool itself does not perform the leak test, but commands the
vehicle’s on-board computer to start the test. Different vehicle manufacturers
might have different criteria and methods for stopping the test once it has been
started. Before starting the Component Test, refer to the vehicle service manual
for instructions to stop the test. For details, refer to Chapter 9 on page.
I/M Readiness
Refer to Chapter 10 on page… for detail.
O2 Mon. Test ( O2 Monitor Test)
OBD II regulations set by the SAE require that relevant vehicles monitor and test
the oxygen (O2) sensors to indentify problems related to fuel efficiency and
vehicle emissions. These tests are not on- demand tests and they are done
automatically when engine operating conditions are within specified limits. These
test results are saved in the on-boards computer’s memory.
More Details check: Autel Maxidas DS708 User Manual
http://www.autelscanner.org/
Subscribe to:
Posts (Atom)